How to use Nanotol Car, Boat & Leisure Cleaner concentrate
- Mixing: The concentrate is mixed 1:25 with water. That is about 40 ml or 4 caps per liter of water. You can use a bucket of water or the Nanotol mix-bottle. This is already included in the set and filled diluted.
- Wet the vehicle.
- Spray the diluted cleaner on the wet, dirty surface.
- Spread the cleaner and let it work for 30-60 seconds. Use the blue sponge cloth included in the set.
- Rinse off: Wash off Nanotol Cleaner and the dirt with plenty of water.
- Dry the vehicle. Use the gray flyffy cloth included in the set for the paint. For the car glass, use a microfiber cloth or the blue Nanotol microfiber cloth included in the set.
TIP: Do not let water dry on the surface to avoid lime stains. An ideal result can be achieved with decalcified water.
How to use Nanotol Car, Boat & Leisure Protector
- Spray Nanotol Protector on the clean surface. Approx. 4 x per square meter.
- Spread the coating very thinly with a clean, lint-free cloth. Ideally, use the white sponge cloth included in the set. Don't use it dry, moisten this lightly to make it smoother. Do this partially to ensure an even distribution. You can take your time for this.
TIP: Proceed in a "checkerboard pattern" - once from left to right and once from top to bottom. - Let dry. A gray haze forms, but it is difficult to see on light and transparent surfaces.
TIP: Heat improves the result. Let your vehicle stand in the sun. - Polish the surface with a high quality microfiber cloth for glass until the surface has become noticeably smoother. Ideally, use the white Nanotol microfiber cloth included in the set.
TIP: If the cloth "slips" over the surface, you have sufficiently activated the Nanotol protective layer.
Needed accessories
Needed accessories
How to use Nanotol Car, Boat & Leisure Cleaner Ready to use
- Wet the vehicle
- Spray the diluted cleaner on the wet, dirty surface.
- Spread the cleaner and let it work for 30-60 seconds. Use the blue sponge cloth included in the set.
- Wash the dirt off with the clean and wet blue Nanotol sponge cloth. If necessary several times.
- Dry off the vehicle. Use the gray Flyffy cloth included in the set for the paint. For the car glass, use a microfiber cloth or the blue Nanotol microfiber cloth included in the set.
TIP: Do not let water dry on the surface to avoid limescale stains. An ideal result can be achieved with decalcified water.
How to use Nanotol Car, Boat & Leisure 1+2
- Wet the vehicle.
- Spray Nanotol 1+2 on the wet surface. Use 6 ml per sqm. This is about 20 sprays for the smaller bottles and 4-5 sprays for the liter bottle.
- Spread the liquid and let the tensides work for 30-60 seconds. Use the blue sponge cloth included in the set or another soft cloth.
- Rinse: wash off Nanotol 1 + 2 and the dirt with plenty of water.
- Dry off the vehicle. Use the gray Flyffy cloth included in the set for the paint. For the car glass, use a microfiber cloth or the blue Nanotol microfiber cloth included in the set.
TIP: Heat improves the result. So enjoy working in the sun. Polishing with the microfiber cloth also generates heat.
If you use Nanotol Auto, Boot & Freizeit 1 + 2 without first applying a basic coating with Nanotol Protector, repeat the process described above twice. The first time it is cleaned and the second time the coating is applied.
How to use Nanotol Auto, Boat & Leisure Set
The set includes two bottles of cleaner (1).
The small bottle contains the detergent concentrate.
The large bottle already contains diluted detergent. You can spray this directly onto the surface with the spray gun. Remove the screw cap and replace it with the enclosed spray gun.
Mix again: As soon as the large bottle is empty, fill 2-4 caps of the cleaner concentrate from the small bottle into the large bottle and fill it up with water. The cleaner stays clean in the spray bottle and can be refilled several times.
TIP: Depending on the degree of soiling, the cleaner can be dosed higher or lower. For normal soiling, 2 caps are sufficient when refilling in the blender bottle.
CLEANING
- Wet the vehicle
- Spray the diluted cleaner on the wet, dirty surface.
- Spread the cleaner and let it work for 30-60 seconds. Use the blue sponge cloth included in the set.
- Wash the dirt off with the clean and wet blue Nanotol sponge cloth. If necessary several times.
- Dry off the vehicle. Use the gray Flyffy cloth included in the set for the paint. For the car glass, use a microfiber cloth or the blue Nanotol microfiber cloth included in the set.
TIP: Do not let water dry on the surface to avoid limescale stains. An ideal result can be achieved with decalcified water.
COATING
- Spray Nanotol Protector on the clean surface. Approx. 4 x per square meter.
- Spread the coating very thinly with a clean, lint-free cloth. Ideally, use the white sponge cloth included in the set. Don't use it dry, moisten this lightly to make it smoother. Do this partially to ensure an even distribution. You can take your time for this.
TIP: Proceed in a "checkerboard pattern" - once from left to right and once from top to bottom. - Let dry. A gray haze forms, but it is difficult to see on light and transparent surfaces.
TIP: Heat improves the result. Let your vehicle stand in the sun. - Polish the surface with a high quality microfiber cloth for glass until the surface has become noticeably smoother. Ideally, use the white Nanotol microfiber cloth included in the set.
TIP: If the cloth "slips" over the surface, you have sufficiently activated the Nanotol protective layer.
You can try Nanotol Car, Boat & Leisure with the Test Set
CLEANING
- Dilute the cleaner (1) with one liter of water.
- Wet the vehicle.
- Spread the diluted cleaner on the wet, dirty surface with a cloth or sponge and let it work for 30-60 seconds.
- Rinse off Nanotol Cleaner and the dirt with plenty of water.
- Dry off the vehicle. It is best to use a lint-free microfiber cloth.
TIP: Do not let water dry on the surface to avoid limescale stains. An ideal result can be achieved with decalcified water.
COATING
- Spray Nanotol Protector on the clean surface. Approx. 4 sprays per square meter.
- Spread the coating very thinly with a clean, lint-free cloth. Do this partially to ensure an even distribution. You can take your time for this.
TIP: Proceed in a "checkerboard pattern" - once from left to right and once from top to bottom. - Let dry. A gray haze forms, but it is difficult to see on light and transparent surfaces.
TIP: Heat improves the result. Let your vehicle stand in the sun. - Polish the surface with the enclosed Nanotol microfiber cloth until the surface has become noticeably smoother.
TIP: If the cloth "slips" over the surface, you have sufficiently activated the Nanotol protective layer.
Viewed