How to use Nanotol Household Cleaner Concentrate
- Mixing: The concentrate is mixed 1:25 with water. That is approx. 40 ml or 4 caps per liter of water. You can use a bucket of water or the Nanotol mixing bottle. This is already included in the set and filled and diluted.
- Wet the surface.
- Spray the diluted cleaner on the wet, dirty surface.
- Spread the cleaner and let it work for 30-60 seconds. Use the blue sponge cloth included in the set. For heavy soiling, we also recommend a rough household sponge to loosen the dirt from the surface after the exposure time.
- Wash the dirt off with the clean and wet blue Nanotol sponge cloth. If necessary several times.
- Dry off the surface. Use a puller, a lint-free cloth or the blue Nanotol microfiber cloth included in the set.
How to use Nanotol Household Protector
- Spray Nanotol Protector on the clean surface. Approx. 4 sprays per square meter.
- Spread the coating very thinly with a clean, lint-free cloth. Ideally, use the white sponge cloth included in the set. Moisten this lightly beforehand to make it smoother. Do this partially to ensure an even distribution. You can take your time for this.
TIP: Proceed in a "checkerboard pattern" - once from left to right and once from top to bottom. - Let dry. A gray haze forms, but it is difficult to see on light and transparent surfaces.
- Polish the surface with a high quality microfiber cloth for glass until the surface has become noticeably smoother. Ideally, use the white Nanotol microfiber cloth included in the set.
TIP: If the cloth "slips" over the surface, you have sufficiently activated the Nanotol protective layer.
Required accessories:
Required accessories:
How to use Nanotol Household Cleaner Ready to use
- Wet the surface.
- Spray the diluted cleaner on the wet, dirty surface.
- Spread the cleaner and let it work for 30-60 seconds. Use the blue sponge cloth included in the set.
- Wash the dirt off with the clean and wet blue Nanotol sponge cloth. If necessary several times.
- Dry off the surface. Use a lint-free cloth, a squeegee or the blue Nanotol microfiber cloth included in the set.
How to use Nanotol Household 1+2
- Wet the surface.
- Spray Nanotol 1+2 on the surface. Use 6 ml per sqm. This is about 20 sprays for the smaller bottles and 4-5 sprays for the liter bottle.
- Spread the liquid and let the surfactants work for 30-60 seconds. Use the blue sponge cloth included in the set or a household sponge.
- Final rinse: Wash off Nanotol 1+2 and dirt with plenty of water.
- Dry off the surface. Use a microfiber cloth for glass or the blue Nanotol microfiber cloth included in the set.
TIP: Heat improves the result. The polishing with the microfiber cloth also generates heat.
If you use Nanotol Household 1+2 without having carried out a previous basic coating with Nanotol Protector, repeat the process described above twice. The first time it is cleaned and the second time the coating is applied.
How to use Nanotol Household Set
The set includes two bottles of cleaner (1).
The small bottle contains the detergent concentrate.
The large bottle already contains diluted detergent. You can spray this directly onto the surface with the spray gun. Remove the screw cap and replace it with the enclosed spray gun.
Mix again: As soon as the large bottle is empty, fill 2-4 caps of the cleaner concentrate from the small bottle into the large bottle and fill it up with water. The cleaner stays clean in the spray bottle and can be refilled several times.
CLEANING
- Mixing: The concentrate is mixed 1:25 with water. That is approx. 40 ml or 4 caps per liter of water. You can use a bucket of water or the Nanotol mixing bottle. This is already included in the set and filled and diluted.
- Wet the surface.
- Spray the diluted cleaner on the wet, dirty surface.
- Spread the cleaner and let it work for 30-60 seconds. Use the blue sponge cloth included in the set. For heavy soiling, we also recommend a rough household sponge to loosen the dirt from the surface after the exposure time.
- Wash the dirt off with the clean and wet blue Nanotol sponge cloth. If necessary several times.
- Dry off the surface. Use a puller, a lint-free cloth or the blue Nanotol microfiber cloth included in the set.
COATING
- Spray Nanotol Protector on the clean surface. Approx. 4 sprays per square meter.
- Spread the coating very thinly with a clean, lint-free cloth. Ideally, use the white sponge cloth included in the set. Moisten this lightly beforehand to make it smoother. Do this partially to ensure an even distribution. You can take your time for this.
TIP: Proceed in a "checkerboard pattern" - once from left to right and once from top to bottom. - Let dry. A gray haze forms, but it is difficult to see on light and transparent surfaces.
- Polish the surface with a high quality microfiber cloth for glass until the surface has become noticeably smoother. Ideally, use the white Nanotol microfiber cloth included in the set.
TIP: If the cloth "slips" over the surface, you have sufficiently activated the Nanotol protective layer.
You can try out Nanotol Household with the Test Set
CLEANING
- Dilute the cleaner (1) with one liter of water.
- Wet the surface.
- Spread the diluted cleaner on the wet, dirty surface with a cloth or sponge and let it work for 30-60 seconds.
- Wash the dirt off with the clean and wet blue Nanotol sponge cloth. If necessary several times.
- Dry off the surface. It is best to use a lint-free microfiber cloth or a squeegee.
COATING
- Spray Nanotol Protector on the clean surface. Approx. 4 sprays per square meter.
- Spread the seal very thinly with a clean, lint-free cloth. Do this partially to ensure an even distribution. You can take your time for this.
TIP: Proceed in a "checkerboard pattern" - once from left to right and once from top to bottom. - Let dry. A gray haze forms, but it is difficult to see on light and transparent surfaces.
TIP: Heat improves the result. Enjoy working in the sun on windows. - Polish the surface with the enclosed Nanotol microfiber cloth until the surface has become noticeably smoother.
TIP: If the cloth "slips" over the surface, you have sufficiently activated the Nanotol protective layer.
Viewed